
Outdoor version of X108G is a compact single conversion HF transceiver covering 0.5 to 30 MHz. Special optimized the Receive Channel, It has lower Background noise; and higher SNR, Up to 0.25uV&12dB;Equipped with a 2.3k SSB filter and a 500 Hz CW narrow-band filter, Excellent filtering characteristics. It include a switchable AGC circuit, Large dynamic range. Other features include a preamplifier and signal attenuator, RIT control for SSB use, and RF output power variable from 1 to 20 Watts. The front panel meter can display incoming signal strength, RF output power and VSWR, and the transceiver includes high VSWR protection circuitry to guard against potential damage to the output stage caused by antenna mismatching. The RF output stage features imported RF MOS tubes and APC circuitry for constant output across all bands. X108G built-in NB modules and a high stability 0.5 ppm TCXO module. It obtained the FCC verification and CE certification. X108G outdoor version equipped with a color OLED solid-state screen, Ignoring the strong outdoor sunlight irradiation, still clear. Has four full aluminum handle for better protect the machine.

The HF bands allow you to communicate over long distances covering many km even to the other side of the world. With the superior performance found in the IC-718 such as wide dvnamic range, high C/N ratio, and full duty operation you will find making these contacts easy. Experience the combination of the latest RF and digital technology, along with the size and simplified operation. You will see the IC-718 will be the most practical rig you will ever own.

Icom changed the way hams think about mobile HC communication in 1995 with the introduction of the IC-706. Since then, the Icom Mobile HF radios have been the Performance HF mobile radio of choice. At the 2012 Tokyo Hamfair, Icom once again changed mobile HF communications by introducing the IC-7100. The ease of operation with fingertip control utilizing the intuitive touch screen interface with the power of 32-bit IF DSP.

Ameritron Al-811 linear amplifier gives you plenty power to bust thru QRM.
You get a quiet desktop linear thats so compact itll slide right into your station -- youll hardly know its there ... until QRM sets in. Conveniently plug it into your nearest 120 VAC outlet -- no special wiring needed. Three tough 811A transmitting tubes, extra heavy duty power supply, all HF band coverage, pressurized ventilation, tuned input, dual illuminated meters, adjustable ALC & more.

No tuning, no fuss, no worries - just turn on and operate ... includes AC power supply, 600 Watts output, continuous 1.5-22 MHz coverage, instant bandswitching, no warm up, no tubes to baby, fully SWR protected, extremely quiet, very compact

The Ameritron ARI-500 Amplifier Radio Interface reads band data from your Icom, Yaesu, Kenwood or Alinco transceiver so they can remotely and automatically bandswitch your ALS-500M amp. Lets you mount your ALS-500M out-of-the-way in your trunk. Works with serial numbers above 13049 (below 13049 requires the ARF-500K). You can add the ALS-500RC for manual bandswitching and data monitoring, etc.

The Yaesu FC-30 Tuner is designed for the FT-897 and FT-897D and bolts to the side of the radio. It covers 1.8 - 30 and 50 - 54 MHz, handling up to 100 watts with a VSWR of 1.5:1 or less. Tuneup power is 4 to 60 watts and tuning takes 5 seconds or less. There are 100 impedance matching memories. This tuner pulls the required 13.7 VDC directly from the transceiver. The impedance matching is 16.5 to 150 ohms and accordingly, the FC-30 should not be expected to match "long wire" type antennas unless specific steps have been taken in the design of the antenna to insure it is within these specifications. Internal DIP switches permit you: to clear memories and/or have the tuner operate during receive.

A4S is the true, high performance tribander. Precisely tuned high-power traps, carefully selected element lengths, and proper spacing combine to make the A4S the preferred antenna for your HF work! This is the premium antenna with all the features that you want. High gain, low SWR, and wide bandwidth keep the contacts coming in. All U-bolts, clamps and hardware are stainless steel. A4S has pinned boom sections and formed aluminum brackets to keep elements straight in all conditions. Our solid construction keeps the A4S on the tower! Add 40 meters with A-744 kit.

The World Ranger Dipole gives bi-directional patterns and rotatable convenience.
You can mount them high and away from the trees for better performance than a wire dipole.
It features high-performance traps, heavy wall tubing, and rugged hardware for years of enjoyment.

The World Ranger Dipole gives bi-directional patterns and rotatable convenience.
You can mount them high and away from the trees for better performance than a wire dipole.
It features high-performance traps, heavy wall tubing, and rugged hardware for years of enjoyment.

- Hi-Fi digital music player; support TF card; support music format: WAV, MP3, WMA, AAC, M4A, FLAC lossless.
- Dimensions : 13.1 x 3.9 x 3.5 in (333 x 100 x 90 mm)Ÿ
- Weight : 40.6 oz (1.15 kg)

Power Sources: 3.7V lithium battery (not included); DC 5V (250mA) external charger (not included)
Unit size: 103 x 62 x 23 mm (W x H x D)
Accessories: carrying strap, USB cable, line-in audio cable, English manual

Power Sources: 3.7V lithium battery (not included); DC 5V (250mA) external charger (not included)
Unit size: 103 x 62 x 23 mm (W x H x D)
Accessories: carrying strap, USB cable, line-in audio cable, English manual

The PL-365/GP-5/SSB is designed for easy one-handed operation in the style of a walkie-talkie. It comes with a unique plug-in rotating ferrite rod antenna for AM and LW, a wire antenna for SW, a belt clip, padded carry pouch with belt loop, ear buds and Owner’s Manual.

Power Sources: UM3 x 3, (AA) Size Batteries or 4.5V DC Adaptor (not included)
Unit Size: 169 x 147 x 55 mm
Accessory: carrying case only.

FM-Stereo /MW/LW/SW SSB/AIR band (118-137 MHz) World Receiver with high sensitivity and selectivity.

Features:
1.FM stereo via earphone or headphone
2.W bandwidth
3.Two kind of build-in antenna, one is telescopic antenna for FM/SW/AIR, the other is 360 degrees rotating MW/LW antenna
4.Auto scan, manual tuning or direct frequency keyin function
5.1000 station memories
6.Antenna Attenuation(ATT) to Enhance reception
7.Squlch control for quality FM and air band listening
8.Wide/narrow bandwidth selection
9.RF gain control knob
10.Three power sources: 4xUM1(D size) batteries; DC 6V;220V AC power (All not included)

SOLAR EMERGENCY RADIO
FM-sterio, Dynamo cranking power for emergency, Tuning and charging LED lights, Flashlight with 3 white LED lights, Red LED light & alert sound, Stereo earphone jack, Cellphone charging USB jack, Solar panel

Dynamo cranking for emergency charging, Emergency smartphone charging via AAA batteries, Ni-MH batteries or direct dynamo cranking (compatible with iPhone 5 and earlier versions), Torch light (can also be used in RADIO POWER OFF mode), Alert siren with flashing red light (can also be used in RADIO POWER OFF mode)

EMERGENCY SMARTPHONE CHARGING
Dynamo radio with cell phone charging, Flashlight, Alert sound with flashing red light, Mini USB jack, Cellphone charging via both Alkaline & Ni-MH batteries

SSB SW SHORTWAVE RADIO
Selective narrow-band short-wave broadband is better than 50dB better than 40dB, Limit noise sensitivity, 4 AA batteries power supply built-in batteries, External power supply 8V 300mA, Machine speaker D77 mm

A storm may arise from a clear sky,so keep the radio GREEN-168 for the rainy day. Built-in generator means that even in the most desperate situations,you still can get the latest local news as well as news from all around the world.
FM/ MW / SW1-2.
High Efficient Power generator for cranking charging
DC USB Jack 5V.
Built-in white LED flashlight,So it is not only perfect for emergencies, but also for camping, hiking, traveling or just relaxing in the backyard.
Earphone Jack.
Built-in Emergency Red LED Light.Siren for S.O.S(especially when you come across disasters such as tsunami,earthquake and so on,high voice).
2.5 inch Speaker with excellent sound quality.
There are four different charging ways: Built-in rechargeable Ni-MH battery (included), 3 x AA batteries (not included), DC USB Jack 5V, Dynamo Crank alone.
Through the radio,you can charge youR phones,MP3 and MP4 (standard USB jack).
Size: 220 x160 x 60mm.

The world’s first self-contained, battery-powered, Multi-mode Portable Transceiver covering the HF, VHF, and UHF bands! Despite its incredibly small size (5.3" x 1.5" x 6.5"), the FT-817 delivers big performance! Its next-generagion PA puts out five watts on all HF bands, plus the 50 MHz, 144 MHz, and 430 MHz bands, on all popular operating modes: USB/LSB/CW/AM/FM/Packet/PSK-31/RTTY. Now the 817 legacy is even better with the introduction of the FT-817ND, which includes coverage of the U.S. 60-meter (5 MHz) band, and it also includes a 1400 mAh NiMH Battery pack (FNB-85) and NC-72B Charger

The worlds's smallest HF/VHF/UHF multimode amateur transceiver. It is the sucessor to the earlier FT-857. But the new D version adds the 60 meter ham band and includes the formerly optional DSP-2 Digital Signal Processing Unit. The FT-857D is loaded with features, high power output and a receiver that blends the renowned performance of the FT-897D and FT-1000 Mark V. It provides coverage of the 160 to 6 meter bands plus the 144 MHz and 430 MHz bands! The ergonomic layout and large tuning knob insure safe mobile operation. And look at the receive coverage: 0.1-56, 76-108, 118-164 and 420-470 MHz The front panel is removable and it is remotable with the optional YSK-857 separation kit. Refinements include: spectrum display, 32 color display, beacon mode, keyer, 200 alphanumeric memories and CTCSS.

The FT-252 is a compact, simple to operate handheld radios that provide up to 5 Watts of RF power, along with loud audio output (800 mW) for the 2 Meter amateur band. The FT-252 ruggedly constructed water resistant body is sealed tight to meet IPX5 protection requirements. It is packed with popular and valuable features demanded by Amateur Radio operators around the world.

This portable frequency counter is designed for counting continuous wave signal comes from Two-way Radio. There are two selectable ranges for you to choose. The ranges cover most of the frequency of the two way radios you want to measure. Its three-button control is easy to use and its small size allows you to carry it anywhere you like.

1. Frequency measurement: 1 MHz --- 2400 MHz
2. Power measurement: 0.1W-- 50W
3. Input impedance: 50 4. Accuracy :140-170 / 400-470 better than 10% 5. Sampling time: about 0.2 sec. 6. Operating temperature :0-40 degrees 7. Battery: three 1.5V AAA alkaline batteries 8. Current consumption: about 100MA 9. Auto power off: approximately 80 seconds

Handheld radio covers 100 kHz to 1300 MHz (less cellular) in: Wide FM, Narrow FM and AM modes. 1000 Alpha memories in 10 banks are supplied. Bandwidths are: FM-N/AM 15 kHz, FM-Wide 220 kHz (-6 dB). 2.4 x 3.7 x 0.9 inches 7.4 oz. SMA type antenna.

» Frequency accuracy: 1k or 0.1K
» Testing distance :UHF: 8m, VHF: 5m.
» Testing range : 50MHz ~ 2.4 GHz
» LCD Display
» Antenna : pulling out antenna
» Battery : 9V
» Full metal case, very durable.

The RT-SRC1+ is a state-of-the-art simplex repeater controller. It employs advanced digital voice recording and processing technology to record the received signal (up to 20 seconds), and retransmit it on a same frequency channel. It is an easy to operate, cost effective and highly flexible platform for extending communication range by converting conventional two-way radio into a simplex repeater system.

The RT-CRC1 is a state-of-the-art cross band duplex repeater controller. It is an easy of operation, cost effective and highly flexible platform for setting up bi-direction cross band duplex repeater with mobile and handheld radio.

Full 1.8-30MHz Operation
Custom designed inductor switch, 1000 volt tuning capacitors, Teflon insulation washers and proper L/C ratio gives you arc-free no worries operation with up to 300 Watts 1.8 to 30 MHz.
Tunes any Antenna
Tunes out SWR on dipoles, verticals, inverted vees, random wires, beams, mobile whips, shortwave receiving antennas.... Nearly anything! Use coax, random wire or balanced lines. Has heavy duty 4:1 balun.
Custom Inductor Switch
The inductor switch is the most likely component to burn up in any antenna tuner. MFJs inductor switch in the MFJ-949E was custom designed to withstand the extremely high RF voltages and currents that are developed in your tuner.
8 Position Super Antenna Switch
Lets you select two coax fed antennas, random wire/balanced line or built-in dummy load through your MFJ-949E or direct to your transceiver.
More hams use MFJ-949s than any other antenna tuner in the world!
Has MFJs full size 3 inch lighted Cross Needle Meter (not a puny "meter" you cant read). Lets you easily read SWR, true peak forward and average reflected power simultaneously on 300 Watt or 30 Watt ranges. Lamp has on/off switch, requires 12 VDC or 110 VAC with MFJ-1312D
QRM-Free PreTune
MFJs QRM-Free PreTune lets you pre-tune your MFJ-949E off-the-air into its built-in dummy load! Makes tuning your actual antenna faster and easier.
Plus much more!
Full size built-in non-inductive 50 Ohm dummy load, scratch-proof Lexan multi-colored front panel, superior cabinet and construction and more!

TUNER, 300W, 1.8-30 MHZ, PEAK CROSS METER, DL
More Hams use MFJ-949s than any other antenna tuner in the world! Why? Because the worlds leading antenna tuner has earned a worldwide reputation for being able to match just about anything. Full 1.8-30MHz Operation Custom designed inductor switch, 1000 volt tuning capacitors, Teflon insulation washers and proper L/C ratio gives you arc-free no worries operation with up to 300 Watts 1.8 to 30 MHz. Tunes any Antenna Tunes out SWR on dipoles, verticals, inverted vees, random wires, beams, mobile whips, shortwave receiving antennas.... Nearly anything! Use coax, random wire or balanced lines. Has heavy duty 4:1 balun. Custom Inductor Switch The inductor switch is the most likely component to burn up in any antenna tuner. MFJs inductor switch in the MFJ-949E was custom designed to withstand the extremely high RF voltages and currents that are developed in your tuner. 8 Position Super Antenna Switch Lets you select two coax fed antennas, random wire/balanced line or built-in dummy load through your MFJ-949E or direct to your transceiver. More hams use MFJ-949s than any other antenna tuner in the world! Has MFJs full size 3 inch lighted Cross Needle Meter (not a puny "meter" you cant read). Lets you easily read SWR, true peak forward and average reflected power simultaneously on 300 Watt or 30 Watt ranges. Lamp has on/off switch, requires 12 VDC or 110 VAC with MFJ-1312D, $14.95 QRM-Free PreTune MFJs QRM-Free PreTune lets you pre-tune your MFJ-949E off-the-air into its built-in dummy load! Makes tuning your actual antenna faster and easier. Plus much more! Full size built-in non-inductive 50 Ohm dummy load, scratch-proof Lexan multi-colored front panel, superior cabinet and construction and more!

VHF AMP,25W IN-160W OUT,144-148 MHZ
MIRAGE’s most popular amplifier gives you 160 Watts of output power for just 25 W in from your base/mobile rig!
The B-2518-G is ideal for your 20 to 60 Watt 2 Meter mobile or base station.
You will talk further, longer, clearer on all modes - FM, SSB, CW- hear weak signals better than you’ve ever heard before!
You get a low noise 20 dB GaAsFET preamp with an excellent 1 dB noise figure for pulling out weak signals.
B-2518-G is fully protected with features found in expensive commercial amplifiers.
High SWR or excessive input power can damage your amplifier. Protection circuits automatically bypass your amplifier to prevent damage and an LED lights to warn you.
An Active-Bias™ system keeps SSB voice crisp and clear for fantastic operation. Other amplifiers using conventional bias methods tend to produce splatter and distortion as power level changes. This amp with Active-Bias™ doesn’t exhibit the problem.
Adjustable time delay gives you smooth transmit/receive switching. Remote external keying. Extra heavy duty custom heatsink spans the entire cabinet. Draws 17 - 22 A from 13.8 VDC. Compact 12" x 3" x 5.5".

DELUXE VOICE KEYER, 8PIN ROUND AND MOD. PLUG
Save Your Voice with the MFJ Contest Voice Keyer
Use 8-pin modular or 8-pin round microphone plug! The MFJ-434B is transparent to your microphone -- your mic’s audio characteristics do not change when your MFJ-434B is installed. Dual controls make it easy to tailor audio level to match your voice. Use 9 Volt battery, 9-15 VDC or 110 VAC with optional MFJ-1312D. Measures a compact 6 ½"W x 2 ½"H x 6 ½"D

TWIN CROSS NEEDLE METER
Monitor 2 radios at once with this new CMX-2300 twin cross needle meter. You can set up an HF radio with the left hand meter, and also watch VHF/UHF settings on the right hand meter. With high power rating (up to 3Kw on HF, and up to 200 watts on VHF) and new twin colour red/green backlighting, the CMX-2300 is set to be a firm favourite.

Advanced high power Switch Mode variable power supply with variable voltage from 1 to 15V rated at 60A continuous. Analogue volts/amp meter, detent on variable power knob for 13.8V and a remote sensing terminal for sensing voltage drop on long line outputs.

The Anderson Powerpole is a family of electrical connectors by Anderson Power Products (APP),although plug compatible connectors are now available from alternate sources. Specific variants of this series of connectors have become de facto standards for conveying "higher power" direct current (DC) electrical power, although these standards are inconsistent and sometimes ignored.

41-07+44-SL : Rain proof Speaker Microphone Fit for ICOM IC-F3 IC -F14 IC-F21
(SL PLUG)

41-07+44-Y7 : Rain proof Speaker Microphone Fit for YAESU VX7R VX177 FT270
(Y7 Plug)

Talk and listen without ever HOLDING your radio!
Push-To-Talk button and microphone are located on the accessory for quick and easy use.
3.5 mm jack for external listen-only earpiece earphone.
A strong swivel retaining clip on the back for convenience.
Heavy duty and Rainproof Design.

41-07+44-K : Rain proof Speaker Microphone Fit
for KENWOOD PUXING WOUXUN (K Plug)

Connector Type:
Right angle SO239 UHF M female connector
Impedance:
50ohm
Connector Material:
Brass
Contact Plating:
Nickel plated
Features:
Weatherproof
Mounting Type:
Cable mount
Cable Type:
rg316 rg174 lmr100
Fixed Mode:
Solder type

The adapter to convert m to N-type connector devices.
Comes in handy when have been the production mix of M-type, N-type connector cable and equipment.

Perfect for 90 degree turns.
Connect UHF male to UHF female.
Great for any project that requires use UHF connectors.
Compatible with all UHF connectors.
This is a commercial series UHF Connector.
One side is UHF Female (outside screw with female pin) and other side is UHF Male (inside screw male pin) at 90 degree angle.
50 Ohm up to 1Ghz
1000 times mating life time.

2 Position Antenna Switch with Lightning Arrest
Better than 60 dB isolation at 300 MHz
Better than 50 dB at 450MHz
Less than 0.2 dB insertion loss
SWR below 1.2:1
SO-239 connectors
Only 3x2x2 inches

(COAX 2WAY SWITCH)
DC ~ 600MHz 2 Position Antenna, Coax Switch, Power: 2.5 kW PEP, 1kW CW, VSWR: Below .12, Insertion Loss: Less than 0.2 dB, Isolation: 60dB 600 MHz, Connetcor: SO-239, Output Port:2.

CERAMIC ANTENNA INSULATORS
The MFJ-16C06 is a six-pack of dog bone ceramic glazed center or end insulators.
It will not break with long antennas and will not arc over or melt even under full legal power. Molded ridges give an extra long path to prevent high voltage breakdown. Smooth wire holes prevent wire damage.
The 16C06s can be used as a center or end insulators for diples, doublets, G5VRs, guy wire, or vees.

Mounts on mast up to 11/4” OD. Super heavy-duty solid aluminum construction. Only MFJ has exclusive, isolated dipole elements that let you insert balun or coil up coax to isolate feedline. Gives you a true balanced dipole that prevents RF on coax shield, eliminates pattern distortion, reduces noise pickup and RFI radiation from coax and provides deep dipole end-nulls for nulling out interference.

Dimensions: W64xH66xD102 / Weight: 440g
Operation Voltage: DC13.8V (10 to 16V)

Mobile Antenna Car trunk Lid / Hatchback / Door Mount
-Color:Black
-Material: Iron
-Compatible with most large VHF/UHF and medium size HF antennas -Easy install on car trunk lid, hatchback, and vertical door -360 degrees rotatable -Dimensions: 3.94 in x 2.56 in x 1.77 in (10.0 cm x 6.5 cm x 4.5 cm) -Weight: 9.24 oz (262 g)

Description:
- 1.7 to 40MHz
- 50 Ohms
- VSWR:Less than 1.5:1
- Max.power rating:1.2kW(PEP)
- Connector:MJ (SO-239)

Standard mobile lip mount cable assembly
Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended
around the connector threads.
16.5 feet of low loss coax, .25" outside diameter
Gold-plated UHF (PL-259/SO-239) connectors

Mount bracket only
black type For roof carrier, mirror stay
Mast diameter accepted:8mm to 32mm

Frequency: DC – 1000 MHz
SWR: less than 1:1 Impedance: 50ohm
Insertion Loss: less than 0.2 dB Max Power Rating: 400w PEP
Connector: UHF female - UHF male Impulse Wave Discharge Voltage: 1000v Impulse Wave Discharge Capacity: 6000A Impulse Wave Retention Discharge Capacity: DC350v ± 20% Insulating Resistance DC100v: Over 10,000M ohms

Covers all bands, 160-10 Meters with antenna tuner. 102 feet long, shorter than 80 Meter dipole. Use as inverted vee or sloper to be more compact. Use on 160 Meters as Marconi with tuner and ground.

Total Size : 35 x 20mm/1.4'' x 0.8'' (L*D);Material : Metal
Color : Silver Tone
Net Weight : 35g
Package Content : 1 x Mini UHF Female to N Male Adapter

Interface: USB to 8 pin
Cable is approximately 39 inch /100cm in length. Build a connection to transfer the information between the radio and computer synchronously. Compatible Models: Yaesu FT-100 / FT-817 / FT-857 / FT-897 / FT-100D / FT-817ND / FT-857D / FT-897D

FLEXIBLE HT ANTENNA
Increase your handheld performance with this high gain antenna. 3 db gain (140-174 MHz), 5 db gain (420-500 MHz) over stock antenna. 15" in length and rated at 10 watts max. Fits most HTs

Frequency 144/430Mhz (2M / 70Cm) Gain (MAX) 2.15 db
Max power 10W
V.S.W.R . Less 1.5 Impedance 50 OHM Length 40CM
Connector SMA
Weight N/A

Frequency 144/430Mhz
Gain (MAX) 3.5 dBi
Max power 10W
V.S.W.R. Less 1.5
Impedance 50 OHM
Length 47cm
Connector SMA-Male
Weight 54g

Frequency: 144/430MHz
Gain: 2.15db
Max power: 10Watts
V.S.W.R: Less 1.5
Impedance: 50 OHM
Connector: SMA TYPE
Length: 210mm
Weight: 38g

Frequency: 144/430MHz
Gain: 2.15db
Max power: 10Watts
V.S.W.R.: Less 1.5

Frequency: 144/430MHz
Gain: 1.8db / 2.5db
Max power: 10Watts V.S.W.R: Less 1.5

MOBILE ANTENNA
HF – 70cm Multi-Band Mobile Antenna  The 40M, 15M and 10M coils come with the antenna and are installed in the photo to the left. The 80M, 20M, 17M coils are optional. Each HF band is tuned by sliding the tuning stubs. 6M/2M/440MHz tuning is pre-set.

Frequency : 144 MHz
Gain : 3.5 dB
Length : 135 cm
VSWR : Less 1.5:1
Impedance : 50 ohms
Connector : UHF(PL-259)
144-174MHz Cut-tuning

Frequency : 144/430 MHz
Gain : 3.0/5.5 dBi
Length : 96 cm
VSWR : Less 1.5:1
Impedance : 50 ohms
Connector : UHF(PL-259)

High gain VHF/UHF base station
antennas.
Special Features: • Fiberglass radomes
• Overlapping outer shells for added strength • Strong waterproof joint couplings • Stainless steel hardware • Wide band performance • Factory adjusted – no tuning required • Highest gain • High wind rating • DC grounded